A torque coefficient compresses thread geometry and friction into a simple estimate of fastener preload. This reference applies NASA’s geometry-based expression to one 1/4-20 UNC example while varying equal thread and bearing friction assumptions. The rows show why one universal K value cannot represent every surface finish, lubricant, washer, and assembled joint.
Bolt Torque and Friction Coefficient Reference table
Calculated bolt torque coefficients for a 1/4-20 thread
NASA equation results for equal thread and bearing friction assumptions on one example thread.
1–4 of 4 matching rows (4 total)
Free engineering resource
Unlock CSV downloads and printing
Enter your email to download the displayed table page as CSV or print it.
CSV and print access for this browser session
Submit the form to unlock CSV downloads and printing.
Search and sort apply to all 4 rows. Print and CSV include only the 4 rows shown on this page.
What K represents
The simplified relationship is T = KFd, where T is torque, F is axial preload, d is nominal diameter, and K combines geometry and friction. It is convenient because the factors fit into one coefficient, but K is not a material constant. Two bolts with the same nominal size can develop different preload under the same wrench reading when surface conditions differ.
Inputs in the table
Each row uses a 60-degree thread with a nominal diameter of 0.25 inch and 20 threads per inch. The mean thread diameter is calculated from the basic 60-degree profile approximation. NASA’s expression combines that diameter, thread helix angle, flank angle, thread friction, and friction under the turned bearing surface. For clarity, each example assigns the same friction coefficient to both contact regions. Real joints can differ.
Reading the friction cases
The table varies both coefficients together from 0.05 to 0.20. As friction rises, calculated K rises, so more torque is needed for the same idealized preload. That trend is not a reason to increase a specified torque. High or poorly controlled friction makes clamp load less predictable, and excessive torque can damage or yield the fastener. Treat these results as sensitivity examples only.
Why friction varies
Thread finish, plating, corrosion protection, lubricant, reuse, contamination, roughness, and washer or flange design influence friction. A lubricant can change thread and bearing friction by different amounts. Embedment and local deformation also change clamp load after tightening. When preload accuracy matters, establish the relationship for the actual hardware and assembly process instead of assuming a generic coefficient.
Torque does not measure preload
A torque wrench measures rotational input, not bolt stretch. Much of that input overcomes friction rather than stretching the fastener. Friction scatter therefore becomes preload scatter. Calibration, wrench technique, tightening sequence, joint compression, and relaxation add further variation. For a narrow clamp-load range, a validated direct tension or joint-specific method may be more suitable.
Keep units consistent
In T = KFd, torque, force, and diameter must use compatible units. Newton-metres with newtons require diameter in metres; inch-pounds with pounds-force require diameter in inches. K has no units. The calculated coefficient transfers between unit systems, but the thread geometry inputs and final torque calculation must remain dimensionally consistent.
Limits and safe use
The equation is a mechanics reference, not an approved torque schedule. It does not account for fastener grade, proof strength, joint separation, external loads, fatigue, gasket response, or failure consequences. NASA’s manual discusses uncertainty in torque measurement. Follow the drawing, manufacturer instructions, governing code, and qualified procedure for an actual assembly, especially where failure could cause injury.
A practical specification checklist
Record fastener size and grade, coating, lubrication, nut and washer details, target preload, tightening method, calibration interval, and sequence. If the supplier or surface treatment changes, verify the torque-tension relationship again. The K equation supports preliminary comparison and education; production control should use actual hardware and validated conditions.
Applying the reference
Before using a row, confirm its units, assumptions, source edition, and fit with the actual project. These values support preliminary learning and comparison; they do not replace an approved drawing, current product data, or qualified review of the actual geometry, material, and operating conditions. Keep the chosen inputs and calculation method with the design record so another engineer can reproduce the result and identify when a different model applies. Recheck the cited source when specifications or product documentation change.
Source
NASA, Fastener Design Manual, RP-1228. The table identifies sourced and calculated values. Accessed October 18, 2026.
