Home » Disc Spring Force and Deflection Examples

Disc springs are conical washers that develop axial load as they flatten. Their force-deflection response depends on the spring geometry, material, manufacturing condition, support, and whether discs are stacked in series or parallel. This comparison shows three SCHNORR standard-material products that share 40 mm outside and 20.4 mm inside diameters but use different thicknesses. The manufacturer lists each load at the defined travel s = 0.75h₀.

Disc spring product examples

MECHANITEC / ENGINEERING REFERENCE

SCHNORR disc spring force and travel examples

Compare three SCHNORR standard-material disc springs with the same outside and inside diameters at the catalog test point s = 0.75 h₀.

1–3 of 3 matching rows (3 total)

SCHNORR disc spring force and travel examples — page 1 of 1
SCHNORR article number Catalog group Outside diameter Dₑ (mm) Inside diameter Dᵢ (mm) Thickness t (mm) Free height l₀ (mm) Cone height h₀ (mm) Travel at s = 0.75 h₀ (mm) Calculated spring force at test travel (N) Test length lₜ (mm)
012 700 C 40 20.4 1 2.3 1.3 0.975 1017 1.325
512 800 B 40 20.4 1.5 2.65 1.15 0.863 2621 1.788
512 900 Internal 2f 40 20.4 2 3.1 1.1 0.825 5701 2.275

Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.

Reading the dimensions

Dₑ is outside diameter, Dᵢ is inside diameter, t is thickness, l₀ is free height, and h₀ is cone height. The catalog’s test travel is 75 percent of h₀. Its force entry is a calculated manufacturer value for the listed test point, not a load curve measured at every possible deflection. The catalog also gives the test length after compression at that point.

Comparing thickness at a shared diameter illustrates why the springs should not be selected by outside size alone. The thicker examples have higher listed force at the same relative test point, while the available travel in millimetres depends on each spring’s cone height. The catalog group labels distinguish the manufacturer’s dimensional series. They do not indicate a universal load class across suppliers.

Stacking and selection

Disc springs can be arranged in series to increase travel or in parallel to increase force, but friction and alignment can affect the ideal result. A stack must be assessed as an assembly, including guides, bearing surfaces, lubrication, and the required load-deflection curve. The single-disc catalog values in this table cannot be multiplied blindly when the actual stack has contact friction or different support conditions.

The cited brochure says the listed spring-steel loads are calculated and that the characteristic curve becomes more progressive beyond 0.75h₀. The table is a limited product comparison, not a full supplier catalog and not a reproduction of the DIN calculation standard. Confirm current availability, material, finish, dimensional tolerances, fatigue requirements, and the exact part number with SCHNORR before ordering or using a spring in a safety-related assembly.

Source

SCHNORR, Original Disc Springs product brochure (February 2024), including its disc spring table notes and standard-material catalog entries.

What the comparison can answer

The table can help screen three part sizes when a designer needs more force within a similar diameter envelope. It also shows that a change in thickness shifts the catalog test force and travel. It cannot tell you which spring is best without the required installed height, minimum and maximum loads, available space, cycle count, temperature, corrosion exposure, and support arrangement.

Check the article number against the current supplier catalog before ordering. Catalogs can change, and the same nominal dimensions may have different material or finish options. Confirm whether the product is delivered lubricated, whether any coating affects friction, and whether the support surfaces satisfy the supplier’s guidance. For a stack, verify the required stack length, number of discs in series and parallel, and alignment method.

In a safety-related assembly, ask the supplier for the current dimensional and load tolerances and a validated load-deflection curve for the chosen part and conditions. A catalog point is a useful comparison, not a guarantee of fatigue life or performance in a particular mechanism.

Do not confuse the cone height h₀ with overall free height l₀: the catalog defines them separately, and the test travel is based on h₀. Verify each value against the supplier’s current dimensional drawing, especially when an equivalent part number is used. Small differences in thickness or free height can produce a different force at the installation height.

Before comparing two candidate springs, also confirm that each supplier expresses the load at the same deflection fraction and test procedure. A peak load, a load at a catalog test point, and a nominal working load are not interchangeable. Recording the installation travel beside the part number makes later selection reviews much easier.