For a round-wire helical spring loaded along its axis, a useful first calculation is the body spring rate: force change divided by deflection. The examples below apply the common relation k = Gd⁴/(8D³Na) using the material moduli and definitions published by Formosa Spring. The dimensions are illustrative inputs chosen for the calculation; they are not catalog parts, recommended sizes, or verified production designs.
Spring-rate examples
Round-wire compression and extension spring rate examples
Formula-based spring-rate examples for round-wire axial spring bodies using two published shear-modulus values.
1–3 of 3 matching rows (3 total)
Free engineering resource
Unlock CSV downloads and printing
Enter your email to download the displayed table page as CSV or print it.
CSV and print access for this browser session
Submit the form to unlock CSV downloads and printing.
Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.
Definitions and units
In the equation, G is the shear modulus in N/mm², d is wire diameter in millimetres, D is mean coil diameter in millimetres, and Na is the number of active coils. The resulting k is in N/mm. If outside diameter is known, the mean coil diameter for round wire is outside diameter minus wire diameter. Keep all dimensions in the same length unit before calculating.
Because wire diameter is raised to the fourth power, small changes in wire size strongly affect rate. Mean diameter is cubed in the denominator, so a larger coil makes the spring softer when the other inputs remain fixed. Active-coil count changes the rate in direct inverse proportion. These relationships help compare candidate geometries before requesting a supplier calculation.
Compression and extension behavior
The table gives the idealized coil-body rate for compression examples and one extension example. An extension spring also has initial tension: its force is not generally zero at the point where the coils first begin to separate. The manufacturer relation expresses extension force as initial tension plus rate multiplied by extension. Hook geometry, body length, initial tension, end transitions, and manufacturing details can change the measured load curve.
The extension example therefore reports the body rate only. It does not predict the force needed to start opening the spring, nor does it calculate force at a complete assembly length. A measured force at a specified length is usually more useful for a purchase specification than a calculated rate alone.
Limits before design use
This calculation does not check corrected wire stress, fatigue life, buckling, solid height, coil clash, tolerances, end-coil activity, temperature, corrosion, or manufacturing capability. Material modulus varies by grade and condition; the two values shown are examples from the cited supplier guide. Critical or highly cycled applications require a complete design method, suitable material data, and supplier validation.
Use the table to understand how inputs affect a first-pass rate estimate. Before building or releasing a design, specify the working deflection range and required load, then confirm the spring’s load at the actual working height. Do not treat the calculated rate as a load rating or safety approval.
Source
Formosa Spring, How to Calculate Spring Rate provides the equation, variable definitions, and example shear moduli used for these calculations.
Worked interpretation
A spring rate of 6 N/mm means that, in the ideal linear region, a further 2 mm of deflection changes the load by about 12 N. It does not say that the spring can safely travel 2 mm or that its starting load is zero. A compression spring can reach solid height; a spring that buckles or exceeds its stress limit can fail before that point. Those checks require geometry beyond the rate equation.
The relationship is sensitive to the input definitions. Use the mean diameter rather than outside diameter, and count only active coils. End coils that touch the adjacent coil are not fully active. If a supplier gives total coil count, confirm how the active count is defined for that spring style. The formula also assumes round wire and a conventional helical body; rectangular wire, conical coils, variable pitch, and unusual end arrangements need a different method.
For a physical assembly, compare calculated rate with a measured load at two specified lengths. The difference divided by the length change gives an observed rate over that interval. This check captures production variation and end effects better than relying on nominal dimensions alone.
Use the table to compare trends, not to infer a complete spring specification. The numerical geometries are examples used to show the equation, and a real order needs drawing tolerances, wire specification, end style, free length, working loads, and surface requirements. If the load curve is nonlinear or the spring is close to its travel limit, request a validated supplier curve instead of extrapolating the rate.
