Home » Metric Coarse Thread Tightening Torque Factors

A nut factor is a compact way to represent how friction in a threaded joint relates applied torque to bolt preload. It is not a material constant or a universal value for an M-size fastener. The calculations below compare two explicitly assumed nut factors at a normalized 1 kN preload for three metric coarse thread sizes. They illustrate the equation only; use tested hardware-specific torque-tension data before selecting an installation torque.

Metric Coarse Thread Tightening Torque Factors

MECHANITEC / ENGINEERING REFERENCE

Illustrative metric coarse-thread torque coefficient calculations

Formula-derived torque examples per 1 kN preload for three common metric coarse-thread nominal diameters and two assumed nut factors.

1–3 of 3 matching rows (3 total)

Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.

NASA describes the simplified relationship as T = KFD, where T is torque, K is the nut factor, F is axial preload and D is nominal fastener diameter. The table uses D in metres, F = 1,000 N and torque in newton-metres. Because this simplified model does not explicitly resolve each friction surface, K must represent the actual hardware and lubrication condition.

For an illustrative calculation, M8 uses a nominal diameter of 8 mm, or 0.008 m. At K = 0.15, T = 0.15 × 1,000 × 0.008 = 1.20 N·m per 1 kN of preload. At K = 0.20, the result is 1.60 N·m per 1 kN. The same proportional relationship gives 0.90 and 1.20 N·m for M6, and 1.50 and 2.00 N·m for M10.

NASA sources discuss K values from specific installation contexts, including a typical lubricated range and an approximate unlubricated value. Those examples do not create a universal “lubricated” or “dry” coefficient. Coatings, plating, washers, surface finish, thread condition, reuse, speed of tightening, cleanliness and lubricant formulation can change the relationship significantly.

The table normalizes the force so the size and assumed K effects are easy to compare. It does not select a target preload. For a real joint, first determine required clamp load and load path, then check bolt proof/yield strength, thread engagement and stripping, bearing stress, joint separation, fatigue, temperature and any applicable code or customer requirement.

Torque-controlled installation has substantial preload scatter. NASA-STD-5020 discusses preload variation and recommends using measured test data when available. A torque wrench reading alone does not establish the exact bolt tension. Where preload is critical, use an approved torque-tension test or a direct tension method such as instrumented bolts, elongation, or a qualified load-indicating process.

The thread labels M6 × 1, M8 × 1.25 and M10 × 1.5 identify common coarse-series examples. Verify the fastener’s exact standard, pitch, class, material, coating and mating hardware. Do not apply these normalized examples to fine-pitch threads, prevailing-torque nuts, lock patches or special aerospace hardware without a qualified method.

A lower K produces a higher calculated preload at the same torque, which can overload a fastener if the assumed friction is too high. A higher K produces a lower preload and may allow joint movement or separation. Evaluate credible upper and lower K values or use test-derived torque limits rather than choosing a coefficient because it makes the desired torque convenient.

Keep the source of K, preload target, thread data, lubrication, surface preparation and tightening sequence with the engineering record. If failure could cause injury or major equipment damage, have a qualified engineer validate the joint and approved installation procedure.

The pitch values in the table identify common ISO metric coarse series examples. Coarse pitch does not determine the joint’s preload capacity by itself; strength class, proof stress, tensile-stress area, engaged thread length and the connected material are separate inputs. Use the thread designation from the actual drawing and check the applicable standard edition.

For a test-based process, measure torque and resulting tension on representative fasteners using the same lubrication, washer, surface finish and tightening method as production. Document sample size and variation. If any component or coating changes, review whether the test remains representative before keeping the same torque limit.

Sources

The relationship and context come from NASA fastener preload and torque guidance. Thread-series designations follow the scope of ISO 261.