Home » Metric Fine Thread Torque Coefficient Examples

The torque coefficient K is a compact way to estimate how tightening torque relates to fastener load and nominal diameter. This table shows formula-derived examples for selected metric fine threads, using two equal-friction assumptions. It is not a torque schedule: actual fastener preload depends on the joint and installation conditions.

Metric Fine Thread Torque Coefficient Examples

MECHANITEC / ENGINEERING REFERENCE

Calculated torque coefficients for selected metric fine threads

Formula-derived K examples for four ISO metric fine-thread sizes under two equal-friction assumptions.

1–8 of 8 matching rows (8 total)

Calculated torque coefficients for selected metric fine threads — page 1 of 1
Metric fine thread Nominal diameter d (mm) Pitch p (mm) Basic pitch diameter d2 (mm) Thread friction μ (dimensionless) Bearing friction μc (dimensionless) Calculated torque coefficient K (dimensionless) Calculation basis
M8×1.00 8 1 7.35 0.1 0.1 0.136 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile
M8×1.00 8 1 7.35 0.15 0.15 0.194 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile
M10×1.25 10 1.25 9.188 0.1 0.1 0.136 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile
M10×1.25 10 1.25 9.188 0.15 0.15 0.194 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile
M12×1.25 12 1.25 11.188 0.1 0.1 0.133 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile
M12×1.25 12 1.25 11.188 0.15 0.15 0.192 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile
M16×1.50 16 1.5 15.026 0.1 0.1 0.132 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile
M16×1.50 16 1.5 15.026 0.15 0.15 0.191 NASA RP-1228 K equation; equal thread and bearing μ; basic 60° profile

Search and sort apply to all 8 rows. Print and CSV include only the 8 rows shown on this page.

NASA RP-1228 describes the simplified relationship T = KFd, where T is torque, F is axial fastener load and d is nominal diameter. The manual calculates K from thread mean diameter, lead angle, thread friction and bearing-surface friction. The equation therefore links thread geometry and surface condition instead of treating K as a fixed material constant.

The examples use M8×1.00, M10×1.25, M12×1.25 and M16×1.50. These are selected fine-pitch combinations from ISO 262. For each row the basic pitch diameter is calculated from the ISO metric 60-degree profile, then used to calculate the lead angle and thread term in the NASA equation.

Two matched friction cases are shown: μ = μc = 0.10 and μ = μc = 0.15. Here μ is thread friction and μc is friction under the turning nut or bolt head. Equal values are used only to make the comparison reproducible. A real bearing surface can have a different finish, coating, washer material or lubricant than the threads.

The fine pitch changes the lead angle relative to a coarse thread of the same nominal diameter. It also changes the basic pitch diameter. Those geometric changes affect the thread component of K. The bearing component in this example uses the simplified NASA model term 0.625 μc, so the results should be read with the stated formula assumptions rather than transferred to arbitrary washer geometry.

A lower K at the same nominal torque would imply a higher calculated axial load in T = KFd, all else equal. That relationship does not mean a designer should choose a lower K or increase the tightening torque. If friction is misestimated, the actual preload may differ materially from the calculation, potentially causing joint separation, yielding, thread damage or fastener failure.

The dataset marks pitch diameter and K as calculated values. ISO sources define the selected thread combinations and basic dimensions; NASA supplies the torque model and friction terms. Rounded values are for comparison. A precision calculation should retain full numerical precision and use verified dimensions, actual friction measurements and the applicable installation standard.

Do not use the table for prevailing-torque nuts, locking patches, thread sealants, damaged threads or lubricated joints unless their additional running torque and friction behavior are included. These conditions can change the measured torque without proportionally changing clamp load. The simple T = KFd equation is a screening approximation, not a substitute for a qualified bolted-joint design.

For critical assemblies, define the fastener class, thread size, engagement, washer or bearing geometry, surface treatments, lubricant and preload requirement. Select a tightening method that can achieve the required preload accuracy and verify it through testing where appropriate. Keep the equation version and friction assumptions with the calculation so another engineer can reproduce the estimate.

ISO 262 identifies selected diameter and pitch combinations, while ISO 724 and ISO 68-1 cover the basic metric thread dimensions and profile. The standard listings do not provide the NASA friction assumptions or endorse the K results. This table combines those inputs explicitly so the source of each calculated field remains clear.

Treat every K value here as one modeled scenario. A change in lubricant, coating, washer, bearing diameter, thread tolerance or tightening procedure can change the result. Use current manufacturer data and a project-approved method for real hardware, and have the responsible engineer review any change to the joint specification.

Sources

Selected thread sizes and profiles are based on ISO 262:2023, ISO 724:2023 and ISO 68-1:2023. The torque equation is from NASA’s RP-1228 Fastener Design Manual.