Home » Roller Chain Sprocket Inspection Tolerances

A sprocket inspection limit is meaningful only when the construction and measured feature are identified. Tsubaki lists face-runout limits for welded teeth on its standard RF sprockets and groups the limits by tooth-root diameter. This quick table preserves those product-specific categories; it is not a general tolerance table for every roller-chain sprocket.

Roller Chain Sprocket Inspection Tolerances

MECHANITEC / ENGINEERING REFERENCE

Tsubaki standard RF sprocket face runout limits

Manufacturer inspection limits for face runout with welded teeth on standard RF sprockets, by tooth-root diameter.

1–3 of 3 matching rows (3 total)

Tsubaki standard RF sprocket face runout limits — page 1 of 1
Sprocket construction Tooth-root diameter band Face runout limit (mm) (mm) Feature checked Application
Standard RF; welded teeth Up to 200 mm 1 Face runout with tooth profile Tsubaki standard RF sprockets
Standard RF; welded teeth 200 to 630 mm 1.5 Face runout with tooth profile Tsubaki standard RF sprockets
Standard RF; welded teeth 630 to 1,250 mm 2.5 Face runout with tooth profile Tsubaki standard RF sprockets

Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.

For a tooth-root diameter up to 200 mm, Tsubaki lists face runout below 1.0 mm. The next category, 200 to 630 mm, lists below 1.5 mm, and 630 to 1,250 mm lists below 2.5 mm. The manual labels the feature as face runout with the tooth profile and ties the values to the welded construction used for standard RF sprockets.

Face runout is an axial variation observed across the sprocket face as the part rotates. It is distinct from tooth-root radial runout, bore concentricity, tooth thickness and chain pitch. A measurement plan should identify the datum, indicator contact point and setup so an inspector checks the same feature and rotation range each time.

Tsubaki notes that its teeth are machined when a conveyor application requires higher precision. That statement matters because the table describes standard welded-tooth products, not a precision-machined sprocket specification. If a conveyor, chain alignment or speed requirement needs tighter control, ask the manufacturer for the appropriate construction and acceptance details.

The diameter category refers to tooth-root diameter, not outside diameter or pitch diameter. Selecting the band from another diameter can produce the wrong comparison. Check the drawing or product catalog for the tooth-root value and confirm that the part is a standard RF sprocket with welded teeth before applying a limit.

These values are useful for a maintenance or incoming inspection reference, but they do not prove that the sprocket is compatible with a particular chain or shaft. Also verify chain series, tooth count, pitch, bore, keyway, alignment, wear and mounting condition. The governing drawing or purchase specification may impose different requirements.

If the reading is above the applicable value, first confirm the measurement setup, datum, indicator condition and whether the sprocket construction matches the cited manual. Record the tooth-root diameter and the maximum observed face runout. Escalate the disposition under the inspection plan rather than assuming that a generic shop tolerance applies.

The source table uses adjacent diameter bands that meet at 200 and 630 mm. For boundary cases, preserve the manufacturer’s printed category and clarify the applicable range with Tsubaki or the controlled drawing. Do not infer an interpolated limit between rows.

A repeatable runout check needs a stable mounting arrangement and a clear datum. Dirt, a damaged bore, keyway burrs, shaft movement or poor support can influence the indicator reading. Clean and mount the sprocket as the inspection procedure requires, rotate it through a full revolution and record the maximum variation at the feature identified by the manual.

Sprocket wear can also affect chain engagement, but the face-runout figures do not measure tooth wear or chain elongation. Inspect the chain and sprocket together when diagnosing noise, vibration or uneven loading. Use the manufacturer’s maintenance guidance for the specific chain series and service conditions, and replace parts according to the documented inspection plan.

Check the sprocket identification and construction before comparing a measurement with this table. Some sprockets are machined from one piece while others have welded hubs or teeth, and the source limits specifically concern welded-tooth standard RF sprockets. A visually similar sprocket from another product series may use a different construction or tolerance. Use the model-specific drawing whenever available.

If the application requires a closer alignment than the listed standard values, specify the required precision before ordering or modifying the part. Tsubaki indicates that tooth machining is available when the conveyor needs higher precision. Any revised requirement should be agreed with the supplier and reflected in the drawing so the inspection criterion is clear to both manufacturing and maintenance.

Sources

The limits are from page 50 of Tsubaki’s Roller Chain & Sprocket Maintenance Manual, under face-runout precision for welded teeth on standard RF sprockets.