Home » HSLA Steel Strength Comparison: Selected Strenx 650 and 700 Grades

High-strength low-alloy steel selection depends on more than the grade number. SSAB publishes thickness-dependent minimum yield strength, tensile strength ranges and elongation for the selected Strenx products in this table. The comparison helps narrow a material search, while keeping each manufacturer product designation and thickness band visible.

HSLA Steel Strength Comparison: Selected Strenx 650 and 700 Grades

MECHANITEC / ENGINEERING REFERENCE

Selected SSAB Strenx 650 and 700 steel mechanical properties

Selected guaranteed strength and elongation properties for named SSAB Strenx 650MC and 700 grades by product form and thickness.

1–15 of 15 matching rows (15 total)

Selected SSAB Strenx 650 and 700 steel mechanical properties — page 1 of 1
Grade and product form Thickness min (mm) Thickness max (mm) Minimum yield strength (MPa) Tensile strength min (MPa) Tensile strength max (MPa) Minimum elongation and gauge length Test orientation
Strenx 650MC D/E 2 3 650 700 850 12% A80 below 3 mm; 14% A5 at and above 3 mm Longitudinal
Strenx 650MC D/E 3.01 6 650 700 850 14% A5 Longitudinal
Strenx 650MC D/E 6.01 8 650 700 850 14% A5 Longitudinal
Strenx 650MC D/E 8.01 10 630 700 850 14% A5 Longitudinal
Strenx 700MC D/E 2 3 700 750 950 10% A80 below 3 mm; 12% A5 at and above 3 mm Longitudinal
Strenx 700MC D/E 3.01 6 700 750 950 12% A5 Longitudinal
Strenx 700MC D/E 6.01 8 700 750 950 12% A5 Longitudinal
Strenx 700MC D/E 8.01 10 680 750 950 12% A5 Longitudinal
Strenx 700 CR 0.7 2.1 700 1000 1200 7% A80 As specified by SSAB product data
Strenx 700 E 4 53 700 780 930 14% A5 Transverse
Strenx 700 E 53.1 100 650 780 930 14% A5 Transverse
Strenx 700 E 100.1 160 650 710 900 14% A5 Transverse
Strenx 700 F 4 53 700 780 930 14% A5 Transverse
Strenx 700 F 53.1 100 650 780 930 14% A5 Transverse
Strenx 700 F 100.1 160 650 710 900 14% A5 Transverse

Search and sort apply to all 15 rows. Print and CSV include only the 15 rows shown on this page.

The records include Strenx 650MC D/E, Strenx 700MC D/E, Strenx 700 CR, Strenx 700 E and Strenx 700 F. These are distinct product names and delivery conditions from SSAB. A higher number in the designation is not enough to assume that two products share the same chemistry, processing route, forming behavior or weldability.

Thickness matters because minimum mechanical properties can change across a product’s dimensional range. Some rows split a single grade into several bands. Read the exact grade and thickness limits together; do not apply a value from a thin sheet to a thicker plate. When the stock thickness falls at a boundary, verify the current product data sheet and purchase specification for the exact interval.

The table records minimum yield strength and tensile strength limits in megapascals, along with the test orientation and elongation gauge notation reported by SSAB. These fields serve different purposes. Yield strength marks the onset of permanent deformation in a tensile test; tensile strength is the maximum engineering stress reached before fracture; elongation is reported for a defined specimen and gauge length.

Minimum yield and tensile values are not a complete material certificate. They do not provide every chemical limit, toughness value, forming radius, fatigue behavior, weld procedure, surface condition or delivery tolerance. Use the exact data sheet and applicable product standard to establish acceptance requirements. A supplier certificate should identify the grade and show the required test results for the delivered heat or coil.

A lighter structure may benefit from higher strength, but strength alone does not determine whether a grade is appropriate. Component geometry, buckling, local stability, fatigue, impact, corrosion, wear, joining and manufacturing capability may control. A designer also has to account for weld heat input, cold-forming strain, springback and the consequences of a crack or permanent deformation in service.

Compare candidate grades at the same thickness and the same test basis. The dataset’s orientation and elongation notation help reveal when values come from different product forms or test directions. If one sheet reports a transverse test and another uses a different orientation or gauge length, the values are not directly equivalent without the governing specifications and product definitions.

The 650 and 700 labels identify selected manufacturer product families, not a universal HSLA grade taxonomy. The table is limited to these SSAB products and the listed thickness bands. It should not be used to infer that other steels with similar names meet the same minimum properties or can be substituted without engineering review.

For a sourcing decision, start with the design’s required strength and thickness, then confirm the product’s forming and joining limits with the supplier. Review the full data sheet, material certificate, applicable standard, dimensional tolerances and delivery condition. If a proposed substitute changes the grade or process, have the responsible engineer assess the component and update the drawing or purchase requirements.

Keep the product source and revision with the comparison. Manufacturers can revise product ranges and technical specifications, and regional product listings can differ. This table is a selected snapshot of SSAB’s listed data, not a guarantee that every product is stocked in every market or that a named product has identical properties in all thicknesses.

The purpose of this comparison is to help readers identify which product data to review next. It does not select a steel for a specific structure. Validate the design using the exact approved material, actual thickness and service requirements, and use the manufacturer’s current documentation when releasing a drawing or order.

Sources

Mechanical-property ranges are transcribed from SSAB’s Strenx 650MC D/E, 700MC D/E, 700 CR, 700 E and 700 F product pages.