Home » Bolt and Nut Friction Coefficients in Torque Calculations

A bolted joint’s tightening torque depends strongly on friction at the threads and under the turning nut or bolt head. NASA RP-1228 gives a compact set of equal-friction examples that makes this sensitivity visible. The values below are model examples for understanding the relationship; they are not a lookup for selecting an installation torque on an actual joint.

Bolt and Nut Friction Coefficients in Torque Calculations

MECHANITEC / ENGINEERING REFERENCE

NASA fastener friction-pair examples and torque coefficients

Four equal-friction pairs from NASA RP-1228 Table VI, with the resulting estimated torque coefficient K.

1–4 of 4 matching rows (4 total)

NASA fastener friction-pair examples and torque coefficients — page 1 of 1
Friction pair Thread friction coefficient μ (dimensionless) Bearing-surface friction coefficient μc (dimensionless) Calculated torque coefficient K (dimensionless) Model basis
μ = μc = 0.05 0.05 0.05 0.074 NASA RP-1228 Table VI; equal thread and bearing friction assumed
μ = μc = 0.10 0.1 0.1 0.133 NASA RP-1228 Table VI; equal thread and bearing friction assumed
μ = μc = 0.15 0.15 0.15 0.189 NASA RP-1228 Table VI; equal thread and bearing friction assumed
μ = μc = 0.20 0.2 0.2 0.25 NASA RP-1228 Table VI; equal thread and bearing friction assumed

Search and sort apply to all 4 rows. Print and CSV include only the 4 rows shown on this page.

The two friction inputs describe different interfaces. Thread friction acts between the mating helical thread flanks. Bearing-surface friction acts under the rotating nut or bolt head against its washer or clamped surface. They can differ because the materials, finish, coating, lubricant and contact pressure at the two locations differ. A single number cannot represent every interface in a fastener assembly.

NASA’s table pairs equal friction coefficients for illustration. When both coefficients are 0.05, the listed torque coefficient K is 0.074. At 0.10, K is 0.133; at 0.15, K is 0.189; and at 0.20, K is 0.250. The increase shows why a torque value computed for one surface condition can produce a different preload when the friction state changes.

The simplified relationship is T = KFd, where T is tightening torque, F is axial fastener load, and d is nominal diameter. K is a calculated torque coefficient, sometimes called a nut factor. It is not itself a coefficient of friction. NASA derives K from thread geometry and both friction inputs, so changing the thread pitch or bearing geometry can change the result even if the friction assumptions stay the same.

For this table, NASA sets the thread and bearing friction values equal to isolate the trend. A real joint may have one coefficient higher than the other. The manual explicitly notes that the two friction values are not necessarily equal. For a controlled installation, use tested friction data for the exact fastener, washer, coating and lubricant combination rather than borrowing a matched pair from this illustration.

Surface preparation can alter the result. Plating, conversion coatings, dry-film lubricants, grease, thread-locking products, reused hardware, dirt and corrosion all affect contact. The bearing face can also differ from the thread surface. Use the condition specified in the drawing and assembly procedure, and keep lubricant type and application consistent across a production run.

Torque is only an indirect way to control bolt tension. A torque wrench controls the applied moment, while much of that moment is spent overcoming friction instead of stretching the fastener. Tool accuracy, operator technique, speed, joint stiffness and embedment add more variation. NASA discusses several preload-measurement methods with different costs and accuracies; the right choice depends on the joint’s criticality.

Do not multiply an arbitrary friction coefficient into a published torque table without checking how that table was derived. A table may assume a particular preload fraction, material strength, friction model and bearing diameter. Altering one input while ignoring the others can yield a misleading torque. Confirm that the equation, units, fastener grade and design factor match the approved calculation.

The four rows are useful for seeing how K changes across selected equal-friction cases. They do not identify a particular lubricant as having exactly one of these values, and they do not cover every coating or fastener material. The dataset preserves the values as NASA’s examples, with the underlying assumptions attached to every record.

For an engineered joint, specify the fastener and mating materials, surface treatment, lubricant, target preload, tightening method and verification method. If preload is safety-critical, use a qualified test or analysis procedure and appropriate inspection. Follow the responsible engineer’s installation specification and the applicable standard rather than treating this reference table as a torque recommendation.

If the joint is reused, repaired or exposed to a different environment, recheck whether the original friction assumptions still apply. A change in lubricant or surface treatment can change preload for the same wrench setting. Keep the approved process attached to the joint documentation so installers do not substitute a nominal K value for the actual fastener and bearing-surface condition.

Sources

The friction-pair values and torque-coefficient relationship are from NASA’s RP-1228 Fastener Design Manual, Table VI and its torque discussion.