Home » Coarse-Pitch Gear Tooth Proportion Examples

Diametral pitch describes how many gear teeth are assigned per inch of pitch diameter. This table works through simple 24-tooth external spur-gear examples at three coarse pitches. It shows basic pitch-circle and tooth-depth relationships for one stated 20-degree full-depth form. The numbers are geometric examples only; they do not rate a gear, specify backlash or establish compatibility with an existing gear.

Coarse-Pitch Gear Tooth Proportion Examples

MECHANITEC / ENGINEERING REFERENCE

Illustrative coarse-pitch 20-degree gear tooth proportions

Formula-derived examples for a 24-tooth external spur gear at selected coarse diametral pitches.

1–3 of 3 matching rows (3 total)

Illustrative coarse-pitch 20-degree gear tooth proportions — page 1 of 1
Diametral pitch P Tooth count z (teeth) Pitch diameter (in) Circular pitch (in) Nominal tooth thickness at pitch circle (in) Addendum (in) Dedendum (in) Whole depth (in) Clearance (in)
4 24 6 0.785 0.393 0.25 0.313 0.563 0.063
8 24 3 0.393 0.196 0.125 0.156 0.281 0.031
16 24 1.5 0.196 0.098 0.063 0.078 0.141 0.016

Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.

For a spur gear, pitch diameter is tooth count divided by diametral pitch. With 24 teeth at 4 diametral pitch, the pitch diameter is 6 inches. At 8 diametral pitch it is 3 inches, and at 16 diametral pitch it is 1.5 inches. The pitch diameter is a theoretical reference circle, not the outside diameter measured across tooth tips.

Circular pitch is the distance along the pitch circle from one tooth to the next and equals pi divided by diametral pitch. Nominal circular tooth thickness is half the circular pitch in an ideal zero-backlash reference. Actual working tooth thickness is adjusted to obtain the required backlash and account for manufacturing tolerances.

The table uses addendum 1/P, dedendum 1.25/P, whole depth 2.25/P and clearance 0.25/P as a classical 20-degree full-depth reference proportion set. Those ratios are assumptions for these calculations. Confirm the specified tooth system and cutter before applying them to a new gear or interpreting a legacy drawing.

A smaller diametral-pitch number means larger teeth: the 4-DP example has a larger addendum and dedendum than the 16-DP example. This relationship helps estimate basic geometry, but strength also depends on face width, material, heat treatment, tooth quality, load spectrum, lubrication and operating temperature.

The gear standard used for a design must match the gear system. AGMA’s published fine-pitch standard treats tooth proportions in its own scope and cautions designers to assess contact ratio, undercutting, clearance, strength and durability. Do not treat a simplified coarse-pitch example as a current AGMA rating method.

To check a mating pair, verify both gears share the same module or diametral pitch and compatible pressure angle and tooth form. Then calculate center distance from pitch diameters and review tooth count, backlash, contact ratio and interference. A matching pitch value alone does not guarantee the gears will mesh correctly.

Low tooth counts deserve particular attention because the tooth root can be undercut and the usable involute may be shortened. Profile shift or a different tooth form can change the result. Consult the governing standard or gear supplier for the actual cutter geometry and allowable design conditions.

The table’s three rows are reproducible calculations from the stated formulas. Rounded values are shown to five decimal places to make the examples easy to follow. If a calculation is used for a drawing, carry sufficient precision internally and apply the tolerances required by the project specification.

This reference does not provide tooth-strength capacity, quality grade, allowable torque, fatigue life or a recommended gear size. Those questions need load, speed, duty cycle, reliability, material, lubrication and manufacturing information that is not present in a geometry-only table.

Before ordering or cutting a gear, compare the drawing against the supplier’s current catalog and the governing gear standard. Ask the gear manufacturer to confirm pitch system, pressure angle, tooth form, backlash and inspection method when replacing a gear whose complete specification is unknown.

These formulas give a first geometry check, not a manufacturing release. Keep the pressure angle, tooth system, profile and backlash assumptions with the calculation so a later reviewer can reproduce the result and detect a mismatch with the gear drawing.

Sources

The calculation scope is limited to the stated simplified proportions. AGMA describes the separate scope of its ANSI/AGMA 1103-H07 fine-pitch standard and highlights checks for contact ratio, undercutting, clearance, strength and durability.