Home » ANSI Running and Sliding Fits RC5 to RC9: Class Index

The RC5–RC9 classes cover the medium through loose end of the ANSI/ASME running and sliding fit family. They are intended for applications where the required running clearance and manufacturing tolerance differ from the closer RC1–RC4 range. This index lists class names and tolerance-zone designations, but not the standard’s size-dependent hole and shaft limits. Select the exact numeric row from the current ASME B4.1 publication.

ANSI Running and Sliding Fits RC5 to RC9: Class Index

MECHANITEC / ENGINEERING REFERENCE

ANSI running and sliding fit classes RC5 to RC9

A class index for the medium through loose running classes in ASME B4.1.

1–5 of 5 matching rows (5 total)

ANSI running and sliding fit classes RC5 to RC9 — page 1 of 1
ANSI/ASME fit class Class name Hole / shaft tolerance class Fit family Dimensional-limit note
RC5 Medium running H8 / e7 running or sliding clearance fit No — obtain the applicable nominal-size row from ASME B4.1
RC6 Medium running H9 / e8 running or sliding clearance fit No — obtain the applicable nominal-size row from ASME B4.1
RC7 Free running H9 / d8 running or sliding clearance fit No — obtain the applicable nominal-size row from ASME B4.1
RC8 Loose running H10 / c9 running or sliding clearance fit No — obtain the applicable nominal-size row from ASME B4.1
RC9 Loose running H11 / c11 running or sliding clearance fit No — obtain the applicable nominal-size row from ASME B4.1

Search and sort apply to all 5 rows. Print and CSV include only the 5 rows shown on this page.

RC5 and RC6 are medium running classes, RC7 is free running, and RC8 and RC9 are loose running classes. The class progression helps communicate the intended relationship between mating cylindrical parts, but the names do not set a numerical clearance for every diameter.

A tolerance-zone designation such as H8/e7 describes a hole zone and a shaft zone within the fit system. To calculate actual limits, start with the basic size and consult the appropriate nominal-diameter interval. A tolerance-class pairing without those limits is incomplete for part manufacture and inspection.

For any pair, minimum diametral clearance is the smallest permitted hole minus the largest permitted shaft. Maximum clearance uses the largest permitted hole minus the smallest permitted shaft. A result that crosses zero is a warning that the selected fit may permit interference or a transition condition under worst-case limits.

A looser running class can accommodate wider tolerances, but it may also allow more radial movement. That movement affects alignment, noise, impact, vibration, sealing and measurement repeatability. Choose a class from the function and tolerance stack, rather than selecting the loosest class simply because it is easier to machine.

Temperature can change the operating gap. Hole and shaft materials may have different thermal expansion, and the two parts may reach different temperatures. A fit that is free at inspection temperature can tighten or loosen in service, so temperature range and heat flow belong in the design analysis when they matter.

Lubrication, contamination and wear also influence practical motion. A larger nominal clearance does not automatically prevent seizure if the shaft deflects, the parts misalign or debris enters the interface. Conversely, excess clearance can reduce positional accuracy or produce impact loading.

The table maps classes to their tolerance-zone pairings and gives the class names. It deliberately does not reproduce ASME’s full size-based dimensional limits. Use the applicable standard table or a licensed calculation tool for the exact basic-size interval and verify the results independently.

When a part is already constrained by a bearing, seal, casting or purchased component, the tolerance system may not be freely chosen. Measure or obtain the controlled dimensions for that component, then set the mating tolerance to produce the required clearance through the full tolerance stack.

Inspection should use the correct instrument range and calibration status. For larger shafts or bores, account for taper, lobing, surface finish and measurement force. A pass at one axial location does not prove the complete functional surface is within tolerance.

ASME lists B4.1-1967 (R2020) as reaffirmed and in effect. Confirm the edition required by the drawing or contract. This RC5–RC9 index is for orientation and class selection; it is not a substitute for the complete standard or a fit-design review.

Do not infer that a loose fit is always acceptable for a low-cost part. Shaft movement can affect alignment, noise, sealing and impact. Select the class against the full assembly requirement, then use the exact size row and verify both clearance extremes. Keep the selected edition, basic diameter and calculated minimum and maximum gaps with the drawing package so manufacturing and inspection use the same controlled values.

Sources

The current B4.1 publication and its scope are listed by ASME. General hole-minus-shaft fit definitions are available in NIST IR 5615.