Home » Spur Gear Tooth Size Calculations

A spur gear’s module and tooth count set its basic reference size. This table gives original metric examples for standard unshifted external gears with a 20° reference pressure angle. It reports the pitch, base, outside, and root diameters plus circular pitch so a reader can check the geometry before moving on to strength and mesh design.

Spur Gear Tooth Size Calculations table

MECHANITEC / ENGINEERING REFERENCE

Standard spur gear tooth size calculation examples

Calculated reference, base, outside, and root diameters for three standard unshifted 20° spur gear examples.

1–3 of 3 matching rows (3 total)

Standard spur gear tooth size calculation examples — page 1 of 1
Module (mm) Number of teeth (teeth) Reference pressure angle (deg) Reference diameter (mm) Base diameter (mm) Outside diameter (mm) Root diameter (mm) Circular pitch (mm)
2 20 20 40 37.588 44 35 6.283
2.5 24 20 60 56.382 65 53.75 7.854
3 30 20 90 84.572 96 82.5 9.425

Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.

Start with the module

Module m is the metric tooth-size parameter, and z is the integer number of teeth. The reference diameter is d = mz. For example, a module-2 gear with 20 teeth has a 40 mm reference diameter. Increasing module while holding tooth count fixed increases the gear’s pitch diameter and tooth scale. The chosen module must match the mating gear and the intended cutter or manufacturing system.

Pitch and tooth spacing

Circular pitch p is the distance measured along the reference circle from one tooth position to the next. For a metric gear, p = πm. The table therefore gives 6.283 mm for module 2, 7.854 mm for module 2.5, and 9.425 mm for module 3. This is a useful consistency check between the stated module and the spacing around the gear, but it does not define backlash or tooth thickness after manufacturing.

Reference and base diameters

The base diameter is db = d cos α, where α is the reference pressure angle. It defines the base circle from which an involute tooth profile is generated. The listed values use 20° and are rounded to three decimal places. A different pressure angle changes the base diameter even when module and tooth count stay fixed, so never compare gears using tooth count alone.

Outside and root diameter assumptions

For the standard unshifted full-depth proportions used here, addendum is one module and the nominal whole depth is 2.25 modules. That gives da = m(z + 2) and df = m(z − 2.5). These proportions provide a basic sizing reference. They are not universal across stub teeth, profile-shifted gears, nonstandard systems, internal gears, or a supplier’s special tooth form.

Read a row as a geometry case

Each record represents one gear, not a meshing pair. The module-2, 20-tooth example is 40 mm at the reference circle and 44 mm at the outside. Its root diameter is 35 mm under the stated standard proportion. The two larger examples use different modules and tooth counts to show how the dimensions scale. No row asserts a specific product, accuracy grade, material, or load capacity.

Mating gears need compatible definitions

Two external gears intended to mesh must use compatible module, pressure angle, tooth system, and manufacturing assumptions. For a simple standard pair, their nominal center distance is half the sum of their reference diameters. A tooth-count ratio describes ideal kinematic speed ratio, but proper operation also depends on center distance, backlash, alignment, tooth quality, and the operating load.

Profile shift changes the result

Profile shift changes tooth proportions and can help address undercut or a required center distance. Once shift is introduced, the standard addendum and root expressions in this table no longer describe every finished dimension without the appropriate corrections. KHK’s technical reference treats profile-shift calculations separately. Use those methods or supplier software when either gear has a nonzero shift coefficient.

What the table leaves out

A diameter chart is not a gear rating. Bending stress, surface durability, contact ratio, root fillet, lubrication, material hardness, heat treatment, duty cycle, and reliability all affect whether a gear can carry the required load. The same nominal tooth geometry can be produced to different accuracy grades and behave very differently at speed. Complete a recognized rating calculation for a power-transmission design.

Manufacturing and inspection

A drawing should make the selected gear system explicit and identify module, pressure angle, tooth count, face width, material, heat treatment, quality level, and any profile shift. Depending on the application, it may also need backlash, runout, lead, profile, and tooth-thickness controls. The outside diameter can be measured with ordinary tools, but that alone cannot verify the involute profile or effective tooth thickness.

Use the values responsibly

The figures are derived from the cited geometric relations and are rounded for convenient reference. Retain more digits in calculations when evaluating center distance or a narrow clearance. Confirm the actual cutter standard and supplier drawing before ordering. If the gear is part of a safety-related or high-energy system, have the full design reviewed with suitable loading, fatigue, lubrication, and failure consequences included.

Source

KHK Gears, Calculation of Gear Dimensions. The table labels which values are sourced and which are calculated. Accessed October 18, 2026.