A compression spring stores energy as its coils shorten under an axial force. Its approximate rate describes the increase in force for each millimetre of deflection while the spring remains in its elastic range. This reference applies the round-wire body equation to three example geometries and reports the assumptions alongside every calculated value.
Compression Spring Design Formulas table
Compression spring design formula examples
Calculated round-wire compression spring rates for three illustrative geometries using manufacturer-published shear moduli.
1–3 of 3 matching rows (3 total)
Free engineering resource
Unlock CSV downloads and printing
Enter your email to download the displayed table page as CSV or print it.
CSV and print access for this browser session
Submit the form to unlock CSV downloads and printing.
Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.
The rate equation
For round wire, the cited relation is k = Gd⁴/(8D³Na). Here G is shear modulus, d is wire diameter, D is mean coil diameter, and Na is the count of active coils. With millimetres for d and D and N/mm² for G, the result is newtons per millimetre. The table carries the material modulus and the chosen geometry so a reader can reproduce each example rather than treating the result as a catalog rating.
Mean diameter and wire size
Mean coil diameter is measured through the wire centreline. When a drawing gives outside diameter, D is approximately OD − d; when it gives inside diameter, D is approximately ID + d. The equation is especially sensitive to d because wire diameter is raised to the fourth power. A small wire-size change can therefore move rate substantially, while adding active coils lowers rate in direct proportion.
How to read the examples
The first row uses the music-wire values shown in the source’s worked calculation, rounded here to a rate of 3.61 N/mm. The other two rows are original calculations with stated assumed dimensions and the same source-listed shear modulus for music wire or stainless 302. They are not measurements. They let a designer see the effect of changing mean diameter, coil count, or wire size before preparing a detailed spring specification.
From rate to force
For a compression spring in its approximately linear range, the load change is ΔF = kΔx. A rate of 3.61 N/mm corresponds to about 18.1 N of additional load over 5 mm of compression, provided the installed spring begins at the reference length used for that calculation. If the spring is already preloaded, add that initial installed force separately. Do not confuse a force change with total load at the operating height.
Active coils and end conditions
Active coils deform during operation; the total coil count also includes end turns that are inactive or partly active. Closed, ground, open, or squared ends change the relationship between total and active turns and affect how a spring seats. The formula table intentionally asks for active coils directly. A drawing or supplier specification should state end style and the method used to count active turns.
Extension springs are different at the ends
The same body-rate expression can estimate the rate of a round-wire extension spring body, but extension springs normally include initial tension. The force relation is therefore F = initial tension + kx after the coils begin separating. Hook geometry, stress concentration, and manufacturing process influence end strength. This article focuses its calculations on compression springs so the example values cannot be mistaken for an extension spring’s complete load curve.
Limits of a first estimate
Rate alone cannot establish whether a spring will reach solid height, buckle, yield, relax, or survive its cycle count. Wire strength, spring index, stress correction, surface condition, end support, temperature, corrosion, and load spectrum all matter. The table is a screening calculation for round-wire helical bodies, not a design check. Compare against supplier data and the applicable design method before building a production part.
Use the calculation as a specification aid
A useful request for quotation pairs rate with the loads at defined lengths, free length, solid height, outside diameter, wire diameter, active and total coils, end configuration, material, finish, tolerance, and expected cycles. The calculated examples help show how geometry affects rate, but a vendor should confirm the delivered spring’s actual performance. For safety-related use, require the material and process documentation appropriate to the application.
Rounding and units
The table reports three decimal places to keep the arithmetic reproducible, not to imply manufacturing precision. Keep units consistent: entering G in MPa is numerically equivalent to N/mm², while D and d must both use millimetres to obtain N/mm. Mixing inch dimensions with metric modulus produces a meaningless result unless all units are converted first. Recalculate from unrounded inputs when comparing close candidates.
Why a single modulus is not universal
The source provides representative moduli for particular spring materials. A real wire specification may vary with grade, processing, temperature, and supplier data. The number used in a preliminary calculation should be replaced by an approved value for the actual wire. Similarly, the round-wire equation assumes a conventional helical spring body and does not cover noncircular wire, conical bodies, variable pitch, or unusual support arrangements.
Practical review sequence
First confirm whether the part is a compression spring and identify the active body turns. Next check the drawing’s diameter definition, wire size, material, and units. Calculate the rate, then translate expected movement into a load change. Finally evaluate stress, solid height, stability, fatigue, tolerances, and environment. This sequence keeps the convenient rate formula in its proper role as one input to a complete design review.
Source
Formosa Spring, How to Calculate Spring Rate. The table labels which values are sourced and which are calculated. Accessed October 18, 2026.
