Home » Helical Gear Tooth Geometry Reference

Helical gear dimensions are described in either a normal system, measured perpendicular to the tooth direction, or a transverse system, measured in the plane of rotation. This table uses the normal system and shows how helix angle changes transverse module, transverse pressure angle, reference diameters, and nominal center distance for three original gear-pair examples.

Helical Gear Tooth Geometry Reference table

MECHANITEC / ENGINEERING REFERENCE

Helical gear tooth geometry examples in the normal system

Original calculations converting normal module and pressure angle to transverse geometry for three unshifted helical gear pairs.

1–3 of 3 matching rows (3 total)

Helical gear tooth geometry examples in the normal system — page 1 of 1
Normal module (mm) Pinion teeth (teeth) Gear teeth (teeth) Reference helix angle (deg) Normal pressure angle (deg) Transverse module (mm) Transverse pressure angle (deg) Pinion reference diameter (mm) Gear reference diameter (mm) Standard center distance (mm)
2 20 40 20 20 2.128 21.173 42.567 85.134 63.851
2.5 24 48 15 20 2.588 20.647 62.117 124.233 93.175
3 30 60 30 20 3.464 22.796 103.923 207.846 155.885

Search and sort apply to all 3 rows. Print and CSV include only the 3 rows shown on this page.

Normal and transverse measurements

Normal module mn is measured perpendicular to the helical teeth. Transverse module mt describes the pitch in the axial view. They are related by mt = mn/cos β, where β is the reference helix angle. As β increases while mn stays fixed, the transverse module increases. That difference matters when calculating the reference diameter and comparing a helical gear to a spur gear.

Pressure angle conversion

The pressure angles also differ between the two systems. The relation used here is tan αt = tan αn/cos β, with αn the normal pressure angle and αt the transverse pressure angle. The calculated angle is slightly larger than the normal angle for a nonzero helix. Keep the specified system attached to every angle and module; using a normal pressure angle where the calculation needs a transverse one can shift downstream geometry.

Reference diameters and centre distance

For an unshifted pair, each reference diameter is d = mtz. The nominal centre distance is half the sum of the pinion and gear reference diameters. The three rows pair 20 with 40 teeth, 24 with 48, and 30 with 60. Each ratio is 2:1, while the module and helix angle vary. These are calculated examples, not dimensions taken from a commercial gearbox.

Hand and helix angle at the mesh

External helical gears that mesh use equal helix-angle magnitude and opposite hands, one left-hand and one right-hand. The handedness allows the teeth to engage correctly across the pair. A single gear’s geometry row does not specify hand, and its numeric angle should not be read as enough information to order a mating pair. Drawings and supplier records need the hand for each member.

Why the normal system is useful

The normal system is common in manufacturing because a hob with a given normal module and normal pressure angle can be used across different helix angles within the same system. The transverse system describes geometry in the plane where the pair meshes. Both are valid, but values must be transformed consistently. KHK’s technical reference explains the two systems and treats profile-shifted calculations separately.

What profile shift does

Profile shift modifies the tooth position relative to the generating rack and can prevent undercut or achieve a target centre distance. The rows here assume zero profile shift. A shifted gear may have different addendum, root diameter, working pressure angle, and centre distance. Do not use the simple formulas in this example to release a shifted design; use a complete calculation in the appropriate system.

Axial thrust and support

Helical teeth engage progressively and can run more smoothly than comparable spur gears, but their geometry creates axial force as well as tangential and radial loads. Bearings, shafts, housings, and lubrication must account for the actual transmitted torque, speed, helix angle, and direction. The table contains no load rating and cannot determine bearing life or housing deflection.

Reading the calculated examples

At a normal module of 2 mm and a 20° helix, the transverse module is about 2.128 mm. The 20-tooth pinion therefore has a reference diameter near 42.567 mm, and its 40-tooth mate is about 85.134 mm. The centre distance follows from those two diameters. Values are rounded for display, so retain unrounded values in a precise layout calculation.

Do not mix modules between catalogs

A gear listing may state normal module, transverse module, or simply module without enough context. Confirm what the supplier means before comparing sizes. A spur gear’s module is ordinarily measured in the transverse plane, while a helical gear’s product and cutter specifications may use the normal system. Matching a number alone does not guarantee compatible tooth spacing or pressure angle.

Design and procurement checks

Before ordering a pair, record the normal or transverse system, module, pressure angle, helix angle, hand, tooth count, profile shift, face width, material, quality class, and required centre distance. Then evaluate tooth strength, contact, backlash, efficiency, noise, lubrication, axial thrust, bearings, and alignment. Ask the supplier for a drawing or calculation that identifies the conventions used for the dimensions.

Source

KHK Gears, Calculation of Gear Dimensions. The table labels which values are sourced and which are calculated. Accessed October 18, 2026.