Home » C93200 Plain Bearing Bronze Properties

C93200 is a leaded tin bronze commonly supplied for bearings and bushings. Its published property values need their qualifiers: tensile and yield strengths are minimums, while hardness and several physical properties are typical. This reference focuses on one named alloy and source so its values are not mistaken for universal properties of every bearing bronze.

C93200 Plain Bearing Bronze Properties table

MECHANITEC / ENGINEERING REFERENCE

Selected C93200 bearing bronze properties

Selected supplier-reported mechanical and physical properties of C93200 with minimum and typical qualifiers.

1–8 of 8 matching rows (8 total)

Selected C93200 bearing bronze properties — page 1 of 1
Alloy Property Reported value Unit Qualifier
C93200 leaded tin bronze Minimum tensile strength 241 MPa Minimum
C93200 leaded tin bronze Minimum yield strength at 0.5% extension 138 MPa Minimum
C93200 leaded tin bronze Minimum elongation in 50 mm 10 % Minimum
C93200 leaded tin bronze Brinell hardness, 500 kg load 65 BHN Typical
C93200 leaded tin bronze Density at 20 °C 8.91 g/cm³ Typical
C93200 leaded tin bronze Machinability rating 70 rating Supplier-listed
C93200 leaded tin bronze Tensile elastic modulus 100000 MPa Typical
C93200 leaded tin bronze Thermal expansion, 20–100 °C 17.3 × 10⁻⁶ 1/°C Typical

Search and sort apply to all 8 rows. Print and CSV include only the 8 rows shown on this page.

What the designation means

C93200 is a copper alloy also called bearing bronze or SAE 660. The designation identifies a composition family, not a complete part specification. The supplier identifies ASTM B505/B505M-23 for reported mechanical requirements. Stock form, casting process, section size, finish, and supplied condition remain important when comparing material data with a drawing or purchase specification.

Minimum strength values

The supplier lists a minimum tensile strength of 241 MPa and a minimum yield strength of 138 MPa, with yield defined at 0.5% extension under load. These are separate measures. A minimum is a lower bound under its stated test context, not an expected value for every sample and not a recommended working stress for a bearing part.

Elongation and hardness

The table reports minimum elongation of 10% over a 50 mm gauge length and Brinell hardness of 65 as typical. The qualifier changes how each number can be used. A typical hardness describes common material behavior but does not establish a guaranteed acceptance threshold. Preserve these labels when copying values into a specification, calculation note, or supplier comparison.

Physical properties for estimates

The source gives density, tensile elastic modulus, and thermal expansion over a stated temperature range. These values can support mass, stiffness, or thermal-growth estimates. Temperature and test definition matter, and actual design inputs should come from the material specification or certificate required for the application. Do not infer full fatigue, wear, or bearing performance from these three physical properties.

Machinability rating

The supplier lists a machinability rating of 70. A rating is comparative and depends on the reference alloy and test convention used by its source. It is not a cutting speed, tool-life promise, or guarantee of chip behavior on a specific machine. Start process planning from current supplier guidance and verify the insert, coolant, rigidity, and surface finish in the intended operation.

Bearing performance takes more than strength

Selection also depends on projected pressure, sliding speed, lubrication regime, shaft material and finish, clearance, heat removal, contamination, and start-stop duty. Strength and hardness alone cannot predict wear or seizure. The table is a material-property starting point; a bearing calculation and review of operating conditions are still required before a design is released.

Product form and certification

Continuous-cast bar, tube, plate, and near-net shapes can have different manufacturing histories and dimensions. The supplier publishes product forms and size schedules separately. Match the purchase description to the required form and standard, then verify traceability. A web property page is useful for orientation but does not replace the certificate attached to the delivered stock.

Use qualifiers carefully

Keep source qualifiers with every value. Do not convert typical hardness into a guaranteed minimum or assume a supplier value applies identically across all product conditions. Confirm the current standard, supplier data, chemistry, test method, and service constraints. A qualified materials or bearing engineer should review critical loading, lubrication, wear, and environment.

Applying the reference

Before using a row, confirm its units, assumptions, source edition, and fit with the actual project. These values support preliminary learning and comparison; they do not replace an approved drawing, current product data, or qualified review of the actual geometry, material, and operating conditions. Keep the chosen inputs and calculation method with the design record so another engineer can reproduce the result and identify when a different model applies. Recheck the cited source when specifications or product documentation change.

Source

Wieland Concast, C93200 Alloy Data. The table identifies sourced and calculated values. Accessed October 18, 2026.